• Skip to primary navigation
  • Skip to main content
  • Skip to primary sidebar
  • Skip to footer

Test & Measurement Tips

Oscilloscopes, electronics engineering industry news, how-to EE articles and electronics resources

  • Oscilloscopes
    • Analog Oscilloscope
    • Digital Oscilloscope
    • Handheld Oscilloscope
    • Mixed-signal Oscilloscope
    • PC-based Oscilloscopes – PCO
  • Design
  • Calibration
  • Meters & Testers
  • Test Equipment
  • Suppliers
  • Video
  • EE Learning Center
You are here: Home / Test and Measurement News / Anechoic chamber, test system get validation for 5G modem development

Anechoic chamber, test system get validation for 5G modem development

April 18, 2019 By Lee Teschler Leave a Comment

Qualcomm Technologies, Inc. a subsidiary of Qualcomm Inc., has accepted Anritsu’s Radio Communication Test Station MT8000A and CATR Anechoic Chamber MA8172A as a validated test method to conduct 5G measurements. The Anritsu solution can be used to perform millimeter-wave (mmWave) beam characterization and beam verification tests for the Snapdragon X50 5G modem using Qualcomm Technologies’ 5G modem development acceleration resource automation software tool.

Beam verification and beam characterization are mandatory processes for 5G MT8000AmmWave mobile device development. The optimized implementation of the Anritsu MT8000A with CATR Chamber for beam characterization and beam verification significantly reduces overall calibration time, as well as the complexity of measurement setup compared to existing solutions. The result is a smaller footprint and lower R&D cost.

The Anritsu MT8000A is common platform to successfully support RF measurement with signalling and beam verification and beam characterization. With this solution, Anritsu is contributing to faster market release of new 5G mobile devices and greatly improves R&D efficiency.

With its leading-edge Non-Standalone (NSA) and Standalone (SA) base station simulation functionality for developing 5G chipsets, Anritsu’s Radio Communication Test Station MT8000A supports the latest 5G technologies, including 4×4 MIMO, to increase data communication speeds in the sub-6 GHz band. It also fully supports 8 CC for wideband mmWave testing and covers all 5G frequency bands to be used during initial 5G deployments, as well as 2.5 GHz, 3.5 GHz, and 4.5 GHz in the FR1 band, together with 28 GHz and 39 GHz in the FR2 band.

The MT8000A is a highly flexible test platform optimized for both protocol and RF testing. The Rapid Test Designer (RTD) software environment delivers an intuitive user interface for creating, executing, and analyzing 5G NSA and SA protocol tests, while the complementary RF measurement software suite provides a flexible and efficient RF test environment for developers of 5G NR chipsets and mobile terminals.

Anritsu Corp., 490 Jarvis Drive, Morgan Hill, CA 95037-2809 U.S.A, www.anritsu.com

You may also like:

  • Keysight
    5G conformance toolset supports validated GCF and PTCRB protocol
  • O-RAN
    O-RAN Alliance develops first open radio access network 5G mmWave…
  • MT1000A
    LG U+ adopts Anritsu MT1000A for 5G rollout
  • keysight
    5G conformance toolset gains GCF approval for 5G NR NSA…

Filed Under: Communication Test, Test and Measurement News Tagged With: anritsucorporation, qualcommtechnologies

Reader Interactions

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

 

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Primary Sidebar

Test & Measurement Handbook


Oscilloscopes Finder

Subscribe to our Newsletter

Subscribe to test and measurement industry news, new oscilloscope product innovations and more.

Subscribe Today

DesignFast

Component Selection Made Simple.

Try it Today
design fast globle

EE TRAINING CENTER CLASSROOMS

“ee

“ee

“ee

“ee

RSS Current EDABoard.com discussions

  • SEPIC Converter Design 12V/2A
  • Capacitor identification in Hughes and Kettner schematic
  • Power controll on 230V with zero switching and PWM?
  • can i use pic mcu as switch on dc-dc step up?
  • How to include a modification in a PIC dev board with PIC16F877A for OVP ?

RSS Current Electro-Tech-Online.com Discussions

  • Hot Rolled Concrete Formwork Tie Rod Z Bar / Dia15/17mm Thread Round steel bar
  • NE555p circuit help
  • Touch circuit sound, led. 555 timer
  • Electronic harrassment...seriously
  • Neon sign transformers for Tesla coil

Follow us on Twitter

Tweets by TestAndMeasure

Footer

EE World Online Network

  • DesignFast
  • EE World Online
  • EDABoard
  • Electro-Tech Online
  • Analog IC Tips
  • Microcontroller Tips
  • Power Electronic Tips
  • Sensor Tips
  • Connector Tips
  • Wire and Cable Tips
  • 5G Technology World

Test & Measurement Tips

  • Subscribe to our newsletter
  • Advertise with us
  • Contact us
  • About us
Follow us on TwitterAdd us on FacebookFollow us on YouTube Follow us on Instagram

Copyright © 2021 · WTWH Media LLC and its licensors. All rights reserved.
The material on this site may not be reproduced, distributed, transmitted, cached or otherwise used, except with the prior written permission of WTWH Media.

Privacy Policy