The GSG-7, the latest Global Navigation Satellite System (GNSS) signal testing solution offered through the Orolia family of Skydel-based simulators, features a small form factor, an internal RF combiner, high-end performance with a 1000 Hz simulation iteration rate, real-time synchronization, Hardware-in-the-Loop (HIL) integration, powerful automation, and multi-constellation and multi-frequency simulations. “The GSG-7 is redefining the […]
Highly-insulated measurement module captures up to 1,500 V for EV testing
The new imc CANSASfit HISO-HV-4 measurement module fills a void in the ever-increasing demands in the e-vehicle and battery testing markets. The new CAN measurement module can be used to perform measurements in high-voltage environments with up to 1500V and extends the range of testing possibilities for test engineers and research and development (R&D) professionals. […]
High-def 12-bit scopes target high-speed signal integrity needs
The HDO Series of High Definition Oscilloscopes features true 12-bit resolution and are available in 70 MHz – 800 MHz bandwidths and two or four channels. The HDO Series is powered by the new UltraVision III platform featuring a custom ASIC chipset, which also provides for dramatically lower front-end noise. The higher resolution and lower […]
Antenna test system enables temperature-controlled measurements, polarization access
The R&S ATS1500C antenna test system from Rohde & Schwarz offers a new temperature test option and a new feed antenna. These additional features enable temperature-controlled measurements in a wide temperature range as well as parallel access to both polarizations, increasing test efficiency and flexibility. The movable R&S ATS1500C is a compact antenna test range […]
Test setup verifies mobile industry processor interface A-PHY layer compliance
A new automotive serializer/deserializer (SerDes) receiver (Rx) compliance test solution verifies mobile industry processor interface (MIPI) A-PHY devices based on the Compliance Test Specification (CTS) requirements. This solution was developed in collaboration with BitifEye Digital Test Solutions GMBH and Wilder Technologies, with the support of Valens Semiconductor Ltd.. Silicon vendors are planning to implement MIPI […]
Protocol test system handles USB Power Delivery, USB Type-C, USB 3.2 link layer compliance testing
The Voyager M4x Analyzer/Exerciser system has been approved by the USB Implementer’s Forum (USB-IF) for USB Power Delivery (USB PD), USB Type-C Functional and USB 3.2 Link Layer compliance testing. The Voyager M4x also supports USB4 logical and protocol layer compliance allowing this single test platform to address the most critical technologies within the USB […]
Intrinsically safe meters simplify mechanical, electrical bond testing
The TEGAM 700 series of bond meters now include two handheld measurement tools. The TEGAM 720A and TEGAM 730A bond meters are suitable for use in the manufacture and maintenance of automotive, aerospace, renewable energy equipment and other applications in which testing of the integrity of mechanical and electrical bonds is a critical requirement. The […]
Ultra-wideband, omnidirectional antennas optimized for radial isotropic measurements from 150 MHz to 18 GHz
Aaronia OmniLOG PRO Omnidirectional Antennas are compact, ultra-wideband omnidirectional antennas suited for radial isotropic use from 150 MHz up to 18 GHz, encompassing most RF sources such as LTE, GSM, UMTS, WLAN, etc. These cost-effective antennas are specified for 1 W cw receive and 100 W cw high-power transmit, making them candidates for broad-range spectrum […]
BNC interface lets piezoelectric sensors hook up to data acquisition gear
A new interface allows the use of IEPE sensors on all data acquisition devices with a 1-MΩ BNC interface. The TA487 IEPE Signal Conditioner is a simple adaptor that allows any PicoScope or oscilloscope to capture and measure signals from a large selection of piezo-electric IEPE sensors, such as the Pico Technology TA095 accelerometer. Integrated […]
Power choke testers measure up To 4 kA/7.7 kJ
The ed-k DPG Power Choke Tester family is a unique series of innovative measurement instruments for inductive power components, using currents up to 4 kA and pulse energy up to 7.7 kJ. The DPG series uses a large-signal impulse measuring method to provide a complete inductance curve as a function of the current L(i), or […]