• Skip to primary navigation
  • Skip to main content
  • Skip to primary sidebar
  • Skip to footer

Test & Measurement Tips

Oscilloscopes, electronics engineering industry news, how-to EE articles and electronics resources

  • Oscilloscopes
    • Analog Oscilloscope
    • Digital Oscilloscope
    • Handheld Oscilloscope
    • Mixed-signal Oscilloscope
    • PC-based Oscilloscopes – PCO
  • Design
  • Calibration
  • Meters & Testers
  • Test Equipment
  • Suppliers
  • Video
  • EE Learning Center
    • Design Guides
      • WiFi & the IOT Design Guide
      • Microcontrollers Design Guide
      • State of the Art Inductors Design Guide
  • FAQs
You are here: Home / Sensing / Control Energy Costs by Using the New APN Series Digital Power Monitor

Control Energy Costs by Using the New APN Series Digital Power Monitor

December 31, 2013 By Test and Measurement Editor Leave a Comment

NK Technologies introduces the APN Series Power Monitoring Sensor. The APN Series Power Monitor measures three phases of current and voltage and computes fourteen values necessary to track power usage in the RS485 Modbus RTU format. The monitor uses current transformers to measure the amperes. The line voltage connects directly to the transducer, up to 600 VAC.

NK-Technologies

“This sensor is a big step forward from analog signal reporting watt consumption to a digital format allowing information on the system voltage, current, and power factor along with wattage,” says Philip Gregory, President, NK Technologies. As the cost of electrical power increases, the desire to use less energy also increases and the need to measure power consumption becomes a necessity, explained Gregory.

Electrical energy is measured in watts over time. To measure watts in an alternating current circuit, the supplied voltage is compared with the current, and whether the current peaks before the voltage (leading power factor in a mostly reactive circuit) or the current peaks after the voltage (lagging power factor in a more inductive circuit), the real power is measured.

“Electronic Smart meters” are used to measure watts, but they only provide information about the entire service consumption. To monitor individual loads or processes, watt transducers or power monitors can be installed. The purpose is to obtain information to help isolate potential problems such as phase loss or voltage sags and voltage spikes, unbalanced current phase to phase, and can help avoid utility surcharges levied for poor power factor.

The APN’s RS485 Modbus RTU format is compatible with many programmable logic controllers and fits seamlessly into industrial communications networks, both hard wired and wireless depending on the specifics of the application. The APN can be configured to accept standard 5 amp current transformer inputs or sensors producing 333mVAC proportional to the AC current of the circuit, or they can use factory matched Rogowski coil inputs. The primary circuit voltage is connected directly to the monitor for 600 VAC or lower, or through a potential transformer for monitoring circuits of higher potentials.

The APN is powered from an external supply, improving measurement accuracy of the measurement data. The APN series also provides a pulse contact to open and close as watt hours are accumulated. This feature allows for a less complex data acquisition device for applications where the need to monitor circuit voltages or the other data points is minimal.

NK Technologies
www.nktechnologies.com

Filed Under: Sensing, Test and Measurement News Tagged With: nktechnologies

Reader Interactions

Leave a Reply Cancel reply

You must be logged in to post a comment.

Primary Sidebar

Current Digital Issue

A frequency you can count on There are few constants in life, but what few there are might include death, taxes, and a U.S. grid frequency that doesn’t vary by more than ±0.5 Hz. However, the certainty of the grid frequency is coming into question, thanks to the rising percentage of renewable energy sources that…

Digital Edition Back Issues

Oscilloscopes Finder

Search Millions of Parts from Thousands of Suppliers.

Search Now!
design fast globle

Subscribe to our Newsletter

Subscribe to test and measurement industry news, new oscilloscope product innovations and more.

Subscribe Today

EE TRAINING CENTER CLASSROOMS

EE Classrooms

RSS Current EDABoard.com discussions

  • Pic 16f877A Hex file
  • Need help to choose accelerometer
  • 7 segment display connections
  • finding attenuation coefficient in CST
  • Effect of variable gain amplifier and LNA on the input RF signal's phase

RSS Current Electro-Tech-Online.com Discussions

  • NOR gate oscillator in LTspice not working
  • How to designing a battery charging indicator circuit for 18650 battery pack
  • ICM7555 IC duty cycle limit at high frequency?
  • I've DESTROYED 3 piezo buttons :((((
  • led doorbell switch

Footer

EE World Online Network

  • DesignFast
  • EE World Online
  • EDABoard
  • Electro-Tech Online
  • Analog IC Tips
  • Microcontroller Tips
  • Power Electronic Tips
  • Sensor Tips
  • Connector Tips
  • Wire and Cable Tips
  • 5G Technology World

Test & Measurement Tips

  • Subscribe to our newsletter
  • Advertise with us
  • Contact us
  • About us
Follow us on TwitterAdd us on FacebookFollow us on YouTube Follow us on Instagram

Copyright © 2022 · WTWH Media LLC and its licensors. All rights reserved.
The material on this site may not be reproduced, distributed, transmitted, cached or otherwise used, except with the prior written permission of WTWH Media.

Privacy Policy