TekDrive is the first native oscilloscope-to-cloud software solution to facilitate global data collaboration directly on an oscilloscope, PC, phone or tablet. Created to enable ultimate ease and accuracy in data accessibility and collaboration, TekDrive provides engineers the ability to instantaneously share and recall data directly on an oscilloscope, eliminating the need for cumbersome data-sharing practices. […]
scope probes and accessories
Debug tookit for DDR5 and LPDDR5 handles 6,400 Mb/sec data rates
A DDR5 Debug Toolkit runs on SDA 8 Zi-B and LabMaster 10Zi-A oscilloscopes. The DDR Debug Toolkit now supports DDR5/LPDDR5 for test, analysis and debug of the entire DDR design cycle. Features include automatic Read/Write burst separation, bursted data jitter analysis, eye diagram mask tests, DDR-specific measurement parameters, and seamless integration with the HDA-125 High-Speed […]
Isolated scope probes feature high bandwidth, dynamic range, CMRR
The second-generation IsoVu Isolated Oscilloscope Probes, called the TIVP Series, extend the applications for isolated probe technology to the entire power system design market with a smaller size, improved ease of use, and enhanced electrical performance. Making accurate measurements on high-speed ungrounded systems can be nearly impossible using traditional differential probes. Engineers working with wide-bandgap […]
Common-mode differential probes excel at 48-V GaN power conversion work
New DL-HCM probes from Teledyne LeCroy target 48-V GaN Power Conversion. They are available in 500 MHz and 1 GHz bandwidth and feature 60 V of common-mode and 80 V differential input range. The 60 V of common mode is well suited for handling any float of the battery and bulk/absorption voltage during charging, while […]
Working with oscilloscope probes, part two
The oscilloscope can be viewed as essentially a voltmeter that incorporates a dynamic display. But the oscilloscope can also make use of a current probe to convert current information into corresponding voltage potentials displayed in units of Amperes. The current-to-voltage conversion takes place within the current probe which operates like the electrician’s clamp-on ammeter. The […]
Basics of oscilloscope probes – Part one
Engineers know what an oscilloscope probe is. It basically permits the user to measure the voltage at any terminal or wire and display the waveform. It usually incorporates a needle point that is capable of getting into a tight place without shorting out to another pin, wire or grounded surface. And it can be equipped […]
High-speed differential probes handle DDR5, LPDDR5 memory signals
The MX0023A InfiniiMax RC is a new high-speed differential probing solution for Double Data Rate 5 (DDR5) and Low Power Double Data Rate 5 (LPDDR5) memory. As data rates of mobile bus systems increase, the edge speed of the signal gets faster, thus requiring higher bandwidth probe solutions. At the same time, many systems deploy […]
Basics of active and differential scope probes
By far the most used oscilloscope probes are the passive 10:1 attenuation probe. It is appropriate when the frequency of the signal under investigation is less than 600 MHz. Impedance matching from the probe tip to channel input port is critical. A mismatch gives rise to reflections, collisions and loss of data. At dc to […]
Probing Small Signals on a High-Voltage Bus
Subtleties of scope probes can lead to garbled measurements when examining power circuits. KEN JOHNSON, DAVID MALINIAK, TELEDYNE LECROY CORP. When an oscilloscope is used for debugging, validation, or device characterization, measurements generally take place with the help of a scope probe. There are several types of scope probes because manufacturers optimize different types for […]
Saelig to stock Teledyne LeCroy HVD3000A Series 1-6kV high-voltage differential probes
The Teledyne LeCroy HVD3000A High-voltage Differential Probes – the 1kV HVD310xA, the 2kV HVD3206A, and the 6kV HVD3605A — are now stocked by Saelig Co. Inc. These probes provide excellent CMRR over a broad frequency range to simplify the measurement challenges found in noisy, high common-mode power electronics environments. The probe’s design makes it easy […]
